In the Bay with Dougie and Eleanor, in conversation.

MOTGuard · In the Bay

Smoke testing

Emissions · 4 min · With Dougie and Eleanor

Listen to this episode

Download audio · Download transcript · Podcast feed

All 40 episodes — choose another
  1. How this works · 2 min
  2. Fog lamps that do not work · 4 min
  3. The extra passenger · 2 min
  4. Reading the beam · 3 min
  5. Before you blame the car · 3 min
  6. Headlamp aim · 3 min
  7. The LED upgrade · 3 min
  8. One lamp, two jobs · 3 min
  9. Refuse or decline? · 4 min
  10. Stopping a test you started · 3 min
  11. Your licence, your name, your record · 3 min
  12. Not fit to test today · 3 min
  13. The log nobody filled in · 3 min
  14. The man reading the notices · 2 min
  15. When it goes wrong · 3 min
  16. The pads you can't see · 3 min
  17. Pipes and hoses · 3 min
  18. Cables, rods and levers · 3 min
  19. Hydraulics · 3 min
  20. Electric parking brakes and four-wheel drive · 3 min
  21. Which test for which vehicle · 3 min
  22. Tread depth · 3 min
  23. Condition, size and type · 3 min
  24. Play you can feel · 3 min
  25. Compliments to the mechanic · 2 min
  26. Ball joints and dust covers · 3 min
  27. Anti-roll bars · 3 min
  28. Subframes · 3 min
  29. Which test applies · 3 min
  30. The kit car · 3 min
  31. A different engine · 3 min
  32. When the book is blank · 3 min
  33. Smoke testing · 4 min
  34. Before the probe goes in · 3 min
  35. The hybrid with a leaking battery · 3 min
  36. Hand controls and the road test · 3 min
  37. You're done. Now what? · 3 min
  38. The quality-control check, including your own · 3 min
  39. Calibration, checks and the certificates · 4 min
  40. Your risk rating and a site review · 3 min

Transcript

ELEANOR: The owner says the diesel passed an informal smoke test on the way here.

DOUGIE: Who conducted that?

ELEANOR: The driver behind him. Through an open window.

DOUGIE: Comprehensive feedback. Wrong equipment.

ELEANOR: We use the approved smoke meter where an instrumented test is required. First we establish that the opacity test applies and the engine is safe to test.

DOUGIE: Then find the manufacturer's smoke plate value. Don't go straight to a familiar default just because you remember where the button is.

ELEANOR: The manual uses the manufacturer's plate information first. Where that information is absent, the default depends on first use and, for older vehicles, whether the engine is turbocharged.

DOUGIE: Read the actual applicable limit. There is more than one, and “diesel” isn't enough information to choose it.

ELEANOR: The current manual also gives a plate-value entry tolerance. Add zero point zero five to the plate value entered into the smoke tester.

DOUGIE: So a plate value of zero point one inverse metres is entered as zero point one five. That's the manual's own example.

ELEANOR: It prevents incorrect failures caused by manufacturing tolerances. It isn't a discretionary allowance for the owner who looks most disappointed.

DOUGIE: Nor something to add again because you like round numbers. Use the current instruction once when entering the plate value.

ELEANOR: With satisfactory engine checks and the prescribed preparation complete, follow the meter's prompts for the acceleration test.

DOUGIE: After the first acceleration, the manual allows a pass if the reading is sixty per cent or less of the vehicle's limit.

ELEANOR: Otherwise, follow the sequence. The mean of the first three readings can establish a pass, or the mean of any three consecutive readings, at or below the limit. There is a maximum of six accelerations in total.

DOUGIE: Consecutive matters. You don't choose your three favourites and arrange an awards ceremony.

ELEANOR: Best Supporting Reading. The competition would be fierce.

DOUGIE: If the first acceleration is significantly higher than the limit, the manual allows you to choose not to complete the test. Six is a maximum, not an instruction to keep going regardless.

ELEANOR: And where a diesel particulate filter is fitted, check that there is no visible smoke from the exhaust during the metered check.

DOUGIE: A satisfactory meter result doesn't cancel that visual check. We haven't finished merely because the screen has stopped arguing.

ELEANOR: On a retest after failure against the manufacturer's plate value, use the same plate value. Don't manufacture a better result by changing the starting point.

DOUGIE: Here's what we do: applicable test, safe engine, correct limit and entry, prescribed sequence, then all the required checks.

ELEANOR: And remember that genuine hybrids, including mild hybrids with electric and combustion engines, are excluded from this opacity test. Separate lamp requirements still apply.

DOUGIE: The chap behind can stand down. His window isn't approved equipment either.

Sources

Source snapshot for this release, published 14/11/2026.

← Back to all episodes